SMH80R46E6.7W2黄山三螺杆泵/SM轻质柴油泵信息

产品详细说明:

SMH80R46E6.7W2黄山三螺杆泵/SM轻质柴油泵

SM three screw pump,SMH three screw pump, three screw pump spot, three screw pump parameters, three screw sizes, three screw structure , three screw pump selection, three screw pump manufacturers, three screw pump, triple screw supply, three screw pump prices, three screw type, how much of a three screw Huangshan Tianman Pump Co., Ltd., three screw pump Dealers, three screw pump repair

●系 列 SM主要特征 中压，单吸轴向力液压平衡最大压力 10.0Mpa最大流量 2200L/min规格范围 40～2200适用介质 轻燃油、轻燃油、重燃油、渣油、废油、导热油、 液压油、润滑油、冷却油、切削冷却液、密封油、油漆、多元醇、异氰酸酯等

●SM三螺杆泵(润滑油泵)螺旋角规格4080120210280440660940130017002200主杆螺旋角3846364246424640464346404640464246424642464246

●安装前检查1．安装前应检查黄山螺杆泵的油封是否良好，并检查泵在运输中是否损坏，可用手转动联轴器是否有卡劲现象，如有则应拆泵进行清洗，修理和校正。2．安装泵的进油和排油管道时，其管径不得小于泵的进油和排油口口径，进油管道不得过长，弯头不得过多，否则将影响泵的工作状态。3．原动机与泵的转向必须一致，严格禁止原动机驱动泵逆转。电机接线时，应先脱开电机与泵的联轴器，对电机作试运转，使其转向与泵的转向标志一致。4．对于在较高温度（60ºC以上）下输送粘度大的油类（如：重油）的备用泵，必须是热备用泵。否则泵在低温下启动会成电机过载或泵损坏。（建议在靠 进泵的排油管上的逆止阀旁，并联安装一个小回流阀，对备用泵可微启回流阀，使泵缓慢逆转，其逆转速<=100转/分，使部分热油经常流过泵内，达到泵 热备用目的）。5．当有两台以上的泵安装在同一条主管线上，为便于泵的启动，在近泵的排油管上必须安装逆止阀。

Application●In heating techniques as fuel oil injection,fuel supply-and transfer pumps.●In the engineering industry as hydranlic, and telemotor pumps.●In the chemical and food industry as cargo-,transfer or supply pumps.●In the marine fidls as transfer-,booster, fuel oil pumps as well for ship hydraulics.

SMH80R46E6.7W2黄山三螺杆泵/SM轻质柴油泵SM三螺杆泵，SMH三螺杆泵，三螺杆泵现货，三螺杆泵参数，三螺杆泵尺寸，三螺杆泵结构图，三螺杆泵选型，三螺杆泵厂家，三螺杆泵组，三螺杆泵供应，三螺杆泵价格，三螺杆泵型号，三螺杆泵多少钱一台，黄山天曼泵业有限公司，三螺杆泵供销商，三螺杆泵维修