PISO-PS600 CR信息

产品详细说明:

	The PISO-PS600 controller combines a new generation processor 1600 MIPS running up to 200 MHz, 9,526 logic element FPGA (Field Programmable Gate Array), I/O buffering circuitry, and motion control characterization software to control the position of 6-axis pulse command Servo/stepper motors. PISO-PS600 not only realizes the motion control with closed-loop (or semi closed-loop) and error handling, but also adopts the feed-forward gain to reduce speed profile following error to meet position control. PISO-PS600 can be used on any IPC with 5 V PCI bus, and is suitable for general-purpose motion applications. This card also contains one FRnet port which allows IPC to expand its ability to have fast digital I/O control easily. This two-wired FRnet can have maximum 128 DI and 128 DO, and they are automatically scanned with a period of 0.72 ms. PISO-PS600 contains a DSP. Apart from a wide speed range, this intelligent motion controller also has a variety of built-in motion control functions, such as 2~6 axis linear interpolation, 2/3-axis circular interpolation, T/S-curve acceleration/deceleration, various synchronous actions, automatic homing, etc. In addition, most of the PISO-PS600 motion control functions are performed with little load on the processor. The motion status, FRnet I/O, and the other I/O cards on IPC can still be monitored while driving. As a result of the low CPU loading requirements of the PISO-PS600, one or more motion cards can be used on a single IPC. ICP DAS has also provided a variety of functions and examples to reduce the need for programming by users, making it a highly cost-effective solution for motion builders.
	·DSP-based motion control card with PCI interface ·Independent 6-axis motion control ·Support both full-closed and semi-closed control modes ·Maximum pulse output frequency: 4 Mpps. ·Maximum Encoder input frequency: 12 Mpps ·4-step home mode with auto-searching ·2 ~ 6-axis linear interpolation function ·2/3-axis circular interpolation function ·Programmable T/S-curve acceleration and deceleration ·Change speed and position on the fly ·High-speed position latch and compare trigger ·Home sensor, positive and negative limit sensors accepted for each axis ·Support fully-functional manual-pulse-generator and jog functions ·Expandable distributed I/Os: 128 DI & 128 DO via two-wired FRnet interface
	·Wafer Cutting ·Laser Cutting ·Toroid Winding Machine ·Tag Printer ·Fix-Pitch Stamping Machine
	PISO-PS600 PCI Bus, High-Speed, DSP-based, 6-axis Motion Control Card with FRnet
	DN-8368GB The Daughter Board is for General Purpose DN-8368MB The Daughter Board is for Mitsubishi J2S Amplifier DN-20M The Daughter Board is for FRnet Connector and Full function Manual-Pulse-Generator CA-MINI68-15 SCSI-II 68-pin Connector Cable 1.5 M CA-SCSI20-M1 SCSI II 20-pin & 20-pin Male Connector Cable 1 M, for Mitsubishi Motor CA-SCSI20-M3 SCSI II 20-pin & 20-pin Male Connector Cable 3 M, for Mitsubishi Motor CA-SCSI20-M5 SCSI II 20-pin & 20-pin Male Connector Cable 5 M, for Mitsubishi Motor CA-2P4C-0100 The Cable for FRnet Modules; Length: 100 M

The PISO-PS600 controller combines a new generation processor 1600 MIPS running up to 200 MHz, 9,526 logic element FPGA (Field Programmable Gate Array), I/O buffering circuitry, and motion control characterization software to control the position of 6-axis pulse command Servo/stepper motors. PISO-PS600 not only realizes the motion control with closed-loop (or semi closed-loop) and error handling, but also adopts the feed-forward gain to reduce speed profile following error to meet position control.

PISO-PS600 can be used on any IPC with 5 V PCI bus, and is suitable for general-purpose motion applications. This card also contains one FRnet port which allows IPC to expand its ability to have fast digital I/O control easily. This two-wired FRnet can have maximum 128 DI and 128 DO, and they are automatically scanned with a period of 0.72 ms. PISO-PS600 contains a DSP. Apart from a wide speed range, this intelligent motion controller also has a variety of built-in motion control functions, such as 2~6 axis linear interpolation, 2/3-axis circular interpolation, T/S-curve acceleration/deceleration, various synchronous actions, automatic homing, etc.

In addition, most of the PISO-PS600 motion control functions are performed with little load on the processor. The motion status, FRnet I/O, and the other I/O cards on IPC can still be monitored while driving. As a result of the low CPU loading requirements of the PISO-PS600, one or more motion cards can be used on a single IPC. ICP DAS has also provided a variety of functions and examples to reduce the need for programming by users, making it a highly cost-effective solution for motion builders. •DSP-based motion control card with PCI interface•Independent 6-axis motion control•Support both full-closed and semi-closed control modes•Maximum pulse output frequency: 4 Mpps.•Maximum Encoder input frequency: 12 Mpps•4-step home mode with auto-searching •2 ~ 6-axis linear interpolation function•2/3-axis circular interpolation function•Programmable T/S-curve acceleration and deceleration•Change speed and position on the fly •High-speed position latch and compare trigger•Home sensor, positive and negative limit sensors accepted for each axis•Support fully-functional manual-pulse-generator and jog functions•Expandable distributed I/Os: 128 DI & 128 DO via two-wired FRnet interface •Wafer Cutting•Laser Cutting•Toroid Winding Machine•Tag Printer•Fix-Pitch Stamping Machine PISO-PS600 PCI Bus, High-Speed, DSP-based, 6-axis Motion Control Card with FRnet DN-8368GB The Daughter Board is for General Purpose DN-8368MB The Daughter Board is for Mitsubishi J2S Amplifier DN-20M The Daughter Board is for FRnet Connector and Full function Manual-Pulse-Generator CA-MINI68-15 SCSI-II 68-pin Connector Cable 1.5 M CA-SCSI20-M1 SCSI II 20-pin & 20-pin Male Connector Cable 1 M, for Mitsubishi Motor CA-SCSI20-M3 SCSI II 20-pin & 20-pin Male Connector Cable 3 M, for Mitsubishi Motor CA-SCSI20-M5 SCSI II 20-pin & 20-pin Male Connector Cable 5 M, for Mitsubishi Motor CA-2P4C-0100 The Cable for FRnet Modules; Length: 100 M The PISO-PS600 controller combines a new generation processor 1600 MIPS running up to 200 MHz, 9,526 logic element FPGA (Field Programmable Gate Array), I/O buffering circuitry, and motion control characterization software to control the position of 6-axis pulse command Servo/stepper motors. PISO-PS600 not only realizes the motion control with closed-loop (or semi closed-loop) and error handling, but also adopts the feed-forward gain to reduce speed profile following error to meet position control.

PISO-PS600 can be used on any IPC with 5 V PCI bus, and is suitable for general-purpose motion applications. This card also contains one FRnet port which allows IPC to expand its ability to have fast digital I/O control easily. This two-wired FRnet can have maximum 128 DI and 128 DO, and they are automatically scanned with a period of 0.72 ms. PISO-PS600 contains a DSP. Apart from a wide speed range, this intelligent motion controller also has a variety of built-in motion control functions, such as 2~6 axis linear interpolation, 2/3-axis circular interpolation, T/S-curve acceleration/deceleration, various synchronous actions, automatic homing, etc.

In addition, most of the PISO-PS600 motion control functions are performed with little load on the processor. The motion status, FRnet I/O, and the other I/O cards on IPC can still be monitored while driving. As a result of the low CPU loading requirements of the PISO-PS600, one or more motion cards can be used on a single IPC. ICP DAS has also provided a variety of functions and examples to reduce the need for programming by users, making it a highly cost-effective solution for motion builders. •DSP-based motion control card with PCI interface•Independent 6-axis motion control•Support both full-closed and semi-closed control modes•Maximum pulse output frequency: 4 Mpps.•Maximum Encoder input frequency: 12 Mpps•4-step home mode with auto-searching •2 ~ 6-axis linear interpolation function•2/3-axis circular interpolation function•Programmable T/S-curve acceleration and deceleration•Change speed and position on the fly •High-speed position latch and compare trigger•Home sensor, positive and negative limit sensors accepted for each axis•Support fully-functional manual-pulse-generator and jog functions•Expandable distributed I/Os: 128 DI & 128 DO via two-wired FRnet interface •Wafer Cutting•Laser Cutting•Toroid Winding Machine•Tag Printer•Fix-Pitch Stamping Machine PISO-PS600 PCI Bus, High-Speed, DSP-based, 6-axis Motion Control Card with FRnet DN-8368GB The Daughter Board is for General Purpose DN-8368MB The Daughter Board is for Mitsubishi J2S Amplifier DN-20M The Daughter Board is for FRnet Connector and Full function Manual-Pulse-Generator CA-MINI68-15 SCSI-II 68-pin Connector Cable 1.5 M CA-SCSI20-M1 SCSI II 20-pin & 20-pin Male Connector Cable 1 M, for Mitsubishi Motor CA-SCSI20-M3 SCSI II 20-pin & 20-pin Male Connector Cable 3 M, for Mitsubishi Motor CA-SCSI20-M5 SCSI II 20-pin & 20-pin Male Connector Cable 5 M, for Mitsubishi Motor CA-2P4C-0100 The Cable for FRnet Modules; Length: 100 M