产品详细说明:
供应0207全系列晶圆电阻(贴片色环电阻),精度0.01%-5%,温度系数5PPM-50PPM,阻值0.01R-10M.可按客户要求定制.具体欢迎咨询.
Type | RJM73P | RJM74M | RJM74P | RJM16M | RJM17M | RJM18M |
Metric type | DIN: 0204 | DIN: 0207 | DIN: 0411 | |
Resistance range | 10Ω to 10MΩ |
Resistance tolerance % | A5(±0.05); B(±0.10); C(±0.25); D(±0.5); F(±1); J(±5%) |
Temperature coefficient(ppm/oC) | C7(±5); C6(±10); C5(±15); C3(±25); C2(±50) |
Climatic category(LCT/UCT/days) | 55/125/56 |
Rated dissipation,P70 | 0.25W | 0.50W | | 1.0W | 2.0W | 3.0W |
Operating voltageUmax | 250V | 300V | 350V | 400V | 450V |
Temperature range | -55oC to 125oC |
Insulation voltage | 300V | 500V | 600V | 700V | 800V | 900V |
Insulation resistance | 1G |
Dimension | ±0.2mm | L=3.5;L1=1.6; D=1.3 | L=5.7; L1=3.5; D=2.1 | L=6.0; L1=3.9; D=2.1 | L=8.7; L1=6.2; D=3.1 | L=11.8; L1=8.8; D=3.6 |
| Kmin=0.8; D1=D+0/D-0.25 | Kmin=1.0; D1=D+0 / D-0.5 | Kmin=1.2;D1=D+0/D-0.5 | D1=D+0/D-0.5; Kmin=1.5 | D1=D+0/D-0.5; Kmin=1.6 |
Soldering bath (recomanded) (mm) | S=1.6; W=2.5; H=2.5 | S=2.6; W=2.5; H=2.5 | S=2.8; W=2.8; H=2.8 | S=5.6; W=3.2; H=3.8 | S=8.2; W=4; H=4.5 |
Outlines | |
Derating curve | |
Test procedures and requirements |
IEC60115-1CLAUSE | IEC60068-2TESTMETHOD | TEST | PROCEDURE | REQUIREMENTSPERMISSIBLE CHANGE (ΔR/R) |
| | Type | | RJM73P, RJM74P | RJM74S, RJM16M | RJM17M, RJM18M |
| | resistance range | | 100Ω to 100kΩ | 100Ω to 470kΩ | 100Ω to 100kΩ |
4.5 |
| tolerance | (%) | ±0.05; ±0.10; ±0.25; ±0.5; ±1.0; ±5.0 |
4.8 |
| temperaturecoefficient | at 25/ 85/ 25oC or under request at 25 / -55 /25oC or at 25 / 125 /25oC | ±5ppm/oC; ±10ppm/oC; ±15ppm/oC; ±25ppm/oC; ±50ppm/oC; ±100ppm/oC; |
4.13 |
| short timeoverload; | room temperature;U=(2.5xP70xR)1/2≤2Umax;5s | ±0.10%+0.05Ω for normal tol.±0.05%+0.05Ω for high precision±0.025%+0.05Ω for ultra high precision | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision |
4.17.2 | 58(Td) | solderability | solder bath method; 215oC; 3s | good tinning ≥95% covered; no visible damage |
4.18.2 | 58(Td) | resistance to soldering heat | solder bath method; 260±5oC; 5 ±1s | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.025%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision |
4.19 | 14 (Na) | rapid change of temperature | 30 minutes at -55oC; 30 minutes at +155oC; 5 cycles | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.025%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision |
4.22 | 6(B4) | vibration | 6h 10 to 2000Hz1.5mm or 196 m/s | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.025%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.05%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.05%+0.05Ω for ultra high precision |
4.23 | | climatic sequence; | | |
4.23.2 | 2(Ba) | dry heat | UCT; 16 h |
4.23.3 | 30(Db) | damp heat, | 55oC; 24h; ≥90% RH |
| cyclic | 1 cycle; |
4.23.4 | 1 (Aa) | cold | LCT; 2 h |
4.23.5 | 13 (M) | low air pressure | 8.5 kPa |
25±10oC 2h; |
4.23.6 | 30(Db) | damp heat | 55oC;24h; ≥90% RH ; | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.05%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.10%+0.05Ω for ultra high precision |
cyclic | 5 cycles; |
| LCT=-55oC; |
| UCT=125oC |
4.24 | 3(Ca) | damp heat, steady state | 40±2oC;56 days | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.05%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.25%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.25%+0.05Ω for ultra high precision |
93 +2/-3% RH |
4.25.1 |
| endurance; standard operation mode | U=(P70xR)1/2≤Umax;1.5 h on; 0.5h off; 70oC; 1000 h | ±0.25%+0.05Ω for normal tol.±0.10%+0.05Ω for high precision±0.05%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.25%+0.05Ω for ultra high precision | ±0.50%+0.05Ω for normal tol.±0.25%+0.05Ω for high precision±0.25%+0.05Ω for ultra high precision |
4.29 | 45 (XA) | component solvent resistance | isopropyl alcohol; +23oC; toothbrush method | marking legible;no visible damage |
RemarkUnliss otherwise specified, all values are tested at the following condition:Temperature: 21oC to 25oC; Relative humidity: 45% to 60% |